1.Determine the location for the three security plates. The two plates go on the equipment to be secured. The 3rd security plate goes on table or desk. Before attaching plates, ensure the cable can run through all three plates.
Note: Be sure the locations you choose do not block any ventilation holes or controls on the equipment.
2.Clean the selected surfaces using the alcohol wipe provided! Omission of this step may result in lack of proper bonding. Do not use any cleaner that leaves a residue, as this prevents adhesive from adhering to the surface.
3.Spread adhesive on one plate and press it onto the selected location. For best results, thinly cover the entire plate with adhesive. Be careful not to use too much adhesive, as it will leak out around the edge of plate.
CAUTION! Loctite 454 gel dries on contact. It can bond to skin and other body tissues in seconds.
Refer to FIRST AID for treatment notes.
1.
4.Wait at least 5 minutes to ensure that adhesive has completely dried. Then route the hole end of cable through each plate.
5.Snap shackle of lock through the hole end of cable to secure the system.
6.To unlock the system, place key in lock and turn
1.
Revolve-A-Lock Installation
1.
1. Loop cable around stationary object and run lock head through loop of cable.
2. Screw lock head into VGA port, LPT port or COM port and twist until tight.
3. Push Button into lock (key not necessary to lock)
TO REMOVE WITH KEY: HOLD REVOLVING DIAL AND UNLOCK PUSH BUTTON. UNSCREW DEVICE.
1
1.
Adapter Plate Instructions
1
1. Clean bottom of adapter plate and objecting securing with alcohol wipes provided.
2. Apply Loctite 454 adhesive thinly to bottom of plate. (Be careful not to use too much adhesive as it will leak out the bottom of the plate)
3. Attach and press plate to object securing.
**Caution Loctite 454 gel dries on contact. It can bond to skin and other body tissues in seconds**
1
Cylinder Lock Instructions
1
1. Remove existing screws from equipment using a screwdriver.
2. Install cylinder locks over screwholes on equipment and reinstall screws through the cylinder.
3. Loop cable around stationary object and run cable through both cylinders.
4. Attach lock at the end of the cable (through the hole).
1
Combination Lock Instructions
1.
1. Leave dials at 0-0-0 and pull out shackle.
2. Rotate shackle halfway around (180o) and push it in as far as possible. While shackle is pressed, turn it one-quarter (90o). Shackle should now be out to the side of the lock.
3. Now set dials to your own (or new) combination.
4. Turn shackle to the 180o position, lift and return to the closed postion...scramble the dials.
1.1.
Cord-A-Keep Instruction
1
1. Use an alcohol prep pad to clean the top and bottom surfaces of each plug, and the
surface area of the product that is to be protected. Dry with a clean paper towel.
Note: If paper towel shows dirt, repeat this step until the surfaces are CLEAN &
DRY
2. Remove a backing sheet from the Super Adhesive and PRESS FIRMLY onto the
plug.
3. Remove the backing sheet on the velcro and install it on the other side of the plug
IMPORTANT: Be sure the velcro fuzz is attached to one plug and the velcro
hooks are attached to the other plug, wall, or product so the plug with the velcro
fuzz can be attached to the plug with the velcro hooks
4. Remove the final backing sheet from adhesive and press the plug firmly into place
onto the product.
**To remove from product, slide wrench over end and twist**
s
Cable Security Ring Instructions
s
1. Pinch the mouse/keyboard cable to form a loop.
2. Push the loop through the oval opening.
3. Run the security cable through the loop and lock it to the desk.
4. The mouse can be removed only when the security cable is removed.
s
TowerLock Instructions
s
TowerLock attaches to the equipment using an existing surface mounted screw on the computer. The shackle of the lock passes through the fastner and prevents access to the screw. The computer cover can not be removed until the lock is removed.
